描述 Description

The UJA1076A core System Basis Chip (SBC) replaces the basic discrete components commonly found in Electronic Control Units (ECU) with a high-speed Controller Area Network (CAN).
The UJA1076A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface.
The core SBC contains the following integrated devices:
High-speed CAN transceiver, inter-operable and downward compatible with CAN transceiver TJA1042, and compatible with the ISO 11898-2 and ISO 11898-5 standards
Advanced independent watchdog (UJA1076A/xx/WD versions)
250 mA voltage regulator for supplying a microcontroller; extendable with external PNP transistor for increased current capability and dissipation distribution
Separate voltage regulator for supplying the on-board CAN transceiver
Serial Peripheral Interface (SPI) (full duplex)
2 local wake-up input ports
Limp-home output port
In addition to the advantages gained from integrating these common ECU functions in a single package, the core SBC offers an intelligent combination of system-specific functions such as:
Advanced low-power concept
Safe and controlled system start-up behavior
Detailed status reporting on system and sub-system levels
The UJA1076A is designed to be used in combination with a microcontroller that incorporates a CAN controller. The SBC ensures that the microcontroller always starts up in a controlled manner.

特性 Features

2.1 General
? Contains a full set of CAN ECU functions:
? CAN transceiver
? Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a microcontroller and peripheral circuitry; an external PNP transistor can be connected for better heat distribution over the PCB
? Separate voltage regulator for the CAN transceiver (5 V)
? Watchdog with Window and Timeout modes and on-chip oscillator
? Serial Peripheral Interface (SPI) for communicating with the microcontroller
? ECU power management system
? Designed for automotive applications:
? Enhanced ElectroMagnetic Compatibility (EMC) performance
? ±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) on the CAN bus pins and the wake-up pins
? ±6 kV ElectroStatic Discharge (ESD) protection IEC 61000-4-2 on the CAN bus pins and the wake-up pins
? ±58 V short-circuit proof CAN bus pins
? Battery and CAN bus pins are protected against transients in accordance with ISO 7637-3
? Supports remote flash programming via the CAN bus
? Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance
? Pb-free; Restriction of Hazardous Substances Directive (RoHS) and dark green compliant
CAN transceiver
? ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver
? Dedicated low dropout voltage regulator for the CAN bus:
? Independent of the microcontroller supply
? Significantly improves EMC performance
? Bus connections are truly floating when power is off
? SPLIT output pin for stabilizing the recessive bus level
Power management
? Wake-up via CAN or local wake-up pins with wake-up source detection
? 2 wake-up pins:
? WAKE1 and WAKE2 inputs can be switched off to reduce current flow
? Output signal (WBIAS) to bias the wake-up pins, selectable sampling time of 16 ms or 64 ms
? Standby mode with very low standby current and full wake-up capability; V1 active to maintain supply to the microcontroller
? Sleep mode with very low sleep current and full wake-up capability
Control and diagnostic features
? Safe and predictable behavior under all conditions
? Programmable watchdog with independent clock source:
? Window, Timeout (with optional cyclic wake-up) and Off modes supported (with automatic re-enable in the event of an interrupt)
? 16-bit Serial Peripheral Interface (SPI) for configuration, control and diagnosis
? Global enable output for controlling safety-critical hardware
? Limp home output (LIMP) for activating application-specific ‘limp home’ hardware in the event of a serious system malfunction
? Overtemperature shutdown
? Interrupt output pin; interrupts can be individually configured to signal V1/V2 undervoltage, CAN/local wake-up and cyclic and power-on interrupt events
? Bidirectional reset pin with variable power-on reset length to support a variety of microcontrollers
? Software-initiated system reset
Voltage regulators
? Main voltage regulator V1:
? Scalable voltage regulator for the microcontroller, its peripherals and additional external transceivers
? ±2 % accuracy
? 3.3 V and 5 V versions available
? Delivers up to 250 mA and can be combined with an external PNP transistor for better heat distribution over the PCB
? Selectable current threshold at which the external PNP transistor starts to deliver current
? Undervoltage warning at 90 % of nominal output voltage and undervoltage reset at 90 % or 70 % of nominal output voltage
? Can operate at VBAT voltages down to 4.5 V (e.g. during cranking), in accordance with ISO 7637 pulse 4/4b and ISO 16750-2
? Stable output under all conditions
? Voltage regulator V2 for CAN transceiver:
? Dedicated voltage regulator for on-chip high-speed CAN transceiver
? Undervoltage warning at 90 % of nominal output voltage
? Can be switched off; CAN transceiver can be supplied by V1 or by an external voltage regulator
? Can operate at VBAT voltages down to 5.5 V (e.g. during cranking) in accordance with ISO 7637, pulse 4
? Stable output under all conditions