最新无码a∨在线观看,一本av高清一区二区三区,亚洲熟妇色l20p,宅男噜噜69av,中出あ人妻熟女中文字幕

TPS61107

適用于單節/兩節電池應用、具有 1.8V 固定輸出電壓的雙路輸出轉換器（升壓直流/直流 + LDO）; ? Synchronous 95% Efficient Boost Converter\n? Integrated 120 mA LDO for Second Output Voltage\n? TSSOP-20 and QFN-24 Package\n? 65 μA (Typ) Total Device Quiescent Current\n? 0.8 V to 3.3 V Input Voltage Range\n? Adjustable Output Voltage up to 5.5 V and Fixed Output Voltage Options\n? Power-Save Mode for Improved Efficiency at Low Output Power\n? Battery Supervision\n? Power Good Output\n? Pushbutton Function for Start-Up\n? Low EMI-Converter (Integrated Antiringing Switch)\n? Load Disconnect During Shutdown\n? Auto Discharge Allows the Device to Discharge Output Capacitor During Shutdown\n? Overtemperature Protection\n? EVM Available (TPS6110XEVM-216)\n? APPLICATIONS \n? All Single or Dual Cell Battery Operated Products Which Use Two System Voltages Like DSP C5X Applications\n? Internet Audio Player, PDAs, Digital Still Cameras and Other Portable Equipment;

The TPS6110x devices provide a complete power supply solution for products powered by either one or two Alkaline, NiCd, or NiMH battery cells. The converter generates two stable output voltages that are either adjusted by an external resistor divider or fixed internally on the chip. It stays in operation with supply voltages down to 0.8 V. The implemented boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency.\n\nThe maximum peak current in the boost switch is limited to a value of 1800 mA.\n\nThe converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. An auto discharge function allows discharging the output capacitors during shutdown mode. This is especially useful in microcontroller applications where the microcontroller or microprocessor should not remain active due to the stored voltage on the output capacitors. Programming the ADEN-pin disables this feature. A low-EMI mode is implemented to reduce ringing and in effect lower radiated electromagnetic energy when the converter enters the discontinuous conduction mode. A power good output at the boost stage provides additional control of cascaded power supply components.\n\n The built-in LDO can be used for a second output voltage derived either from the boost output or directly from the battery. The output voltage of this LDO can be programmed by an external resistor divider or is fixed internally on the chip. The LDO can be enabled separately i.e., using the power good of the boost stage.\n\n The device is packaged in a 20-pin TSSOP (20 PW) package or in a 24-pin QFN (24 RGE) package.

TPS61107

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107PW

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107PW

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107PW

開關穩壓器 3.3V Boost Cnvrtr w/1.8V 120mA LDO;

TPS61107PWG4

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107PWR

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107RGE

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107RGER

DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER

TPS61107RGER

開關穩壓器 3.3V Boost Cnvrtr w/1.8V 120mA LDO;