Z86L990屬于開發板套件編程器的編程器仿真器調試器。由Zilog, Inc.制造生產的Z86L990編程器，仿真器和調試器編程器、仿真器和調試器是在嵌入式系統中用于編寫/加載/測試軟件的器件。配套使用/相關產品包括 AEAT、Altera、Arduino、ARM、ATiny、AVR、Basic Stamp、Blackfin、ChromeOS、Code Warrior、ColdFire、Cortex、DaVinci Boards、Digilent、EEPROM、Encoders、FPGA、Freescale、Intel、JTAG Devices、Kinetis、Lapis、Lattice、Magnetic Position Sensors、MSP430、PIC、Zilog、ZON 等制造商的產品。

Architectural Overview

The Z86D99 is a low-voltage general-purpose one-time programmable (OTP) Z8? microcontroller with an integrated four-channel 8-bit sigma delta analog-to-digital converter. The Z86L99 is the read-only memory (ROM) version of this controller.

特性 Features

? Four-channel, 8-bit sigma delta analog-to-digital (A/D) converter with external

voltage references (not available in the 28-pin configuration)

? Two independent analog comparators

? Controlled current output

? 489 bytes of RAM

– 233 bytes of general-purpose register-based RAM

– 256 bytes of RAM mapped into the program memory space that can be

used as data RAM or executable RAM

? 32 Kbytes of OTP memory (Z86D99X)

? 16 Kbytes of ROM (Z86L99X)

Counter/Timers

? Special architecture to automate generation and reception of complex pulses

or signals:

– Programmable 8-bit counter/timer (T8) with two 8-bit capture registers and

two 8-bit load registers

– Programmable 16-bit counter/timer (T16) with one 16-bit capture register

pair and one 16-bit load register pair

– Programmable input glitch filter for pulse reception

? One general-purpose 8-bit counter/timer (T1) with 6-bit prescaler

Input/Output and Interrupts

? Thirty-two I/Os, twenty-nine of which are bidirectional I/Os with programmable

resistive pull-up transistors (24 I/Os are available in the 28-pin configuration)

? Sixteen I/Os are selectable as stop-mode recovery sources

? Six interrupt vectors with nine interrupt sources

– Three external sources

– Two comparator interrupts

– Three timer interrupts

– One low-battery detector flag

Operating Characteristics

? 8-MHz operation

? 3.0 V to 5.5 V operating voltage (Z86D990/Z86D991)

? 2.3 V to 5.5 V operating voltage (Z86L990/Z86L991)

? Low power consumption with three standby modes:

– Stop

– Halt

– Low Voltage Standby

? Low-battery detection flag

? Low-voltage protection circuit (also known as VBO, or voltage brownout,

circuit)

? Watch-dog timer and power-on reset circuits

User-Programmable Option Bits

? Clock source—RC/other (LC, resonator, or crystal)

? Watch-dog timer permanently enable

? 32-kHz crystal

? Port 20–27 pull-up resistive transistor

? Port 40–42 pull-up resistive transistor

? Port 44–47 pull-up resistive transistor

? Port 50–51 pull-up resistive transistor

? Port 54–57 pull-up resistive transistor

? Port 60–63 pull-up resistive transistor (not available in Z86D991/Z86L991)

? Port 64–67 pull-up resistive transistor (not available in Z86D991/Z86L991)

? P43 high impedance in STOP mode (available in OTP only)

Force P43 to output a 1 in the open-drain configuration