TLV1544CPW屬于集成電路（IC）的模數轉換器（ADC）。由美國德州儀器公司制造生產的TLV1544CPW模數轉換器（ADC）模數轉換器（ADC、A/D 或 A 轉 D）對模擬信號進行采樣，例如由麥克風采集的聲音或傳感器的輸出，然后將其轉換為數字信號。一般來說，數字輸出是二進制補碼二進制數，與輸入成比例。輸入類型可能是差分、偽差分或單端輸入。模數轉換器可按照位數、采樣率、輸入數、接口、轉換器數和架構（例如自適應增量、雙斜率、折疊、流水線、SAR、三角積分、兩步式）進行選擇。

Conversion Time 3 10 ms

10-Bit-Resolution ADC

Programmable Power-Down

Mode . . . 1 mA

Wide Range Single-Supply Operation of

2.7 V dc to 5.5 V dc

Analog Input Range of 0 V to VCC

Built-in Analog Multiplexer with 8 Analog

Input Channels

TMS320 DSP and Microprocessor SPI and

QSPI Compatible Serial Interfaces

End-of-Conversion (EOC) Flag

Inherent Sample-and-Hold Function

Built-In Self-Test Modes

Programmable Power and Conversion Rate

Asynchronous Start of Conversion for

Extended Sampling

Hardware I/O Clock Phase Adjust Input

description

The TLV1544 and TLV1548 are CMOS 10-bit

switched-capacitor successive-approximation (SAR)

analog-to-digital (A/D) converters. Each device

has a chip select (CS), input-output clock (I/O

CLK), data input (DATA IN) and serial data output

(DATA OUT) that provide a direct 4-wire

synchronous serial peripheral interface (SPIE,

QSPIE) port of a host microprocessor. When

interfacing with a TMS320 DSP, an additional

frame sync signal (FS) indicates the start of a

serial data frame. The devices allow high-speed

data transfers from the host. The INV CLK input

provides further timing flexibility for the serial

interface.

In addition to a high-speed converter and versatile

control capability, the device has an on-chip

11-channel multiplexer that can select any one of

eight analog inputs or any one of three internal self-test voltages. The sample-and-hold function is automatic

except for the extended sampling cycle, where the sampling cycle is started by the falling edge of asynchronous

CSTART. At the end of the A/D conversion, the end-of-conversion (EOC) output goes high to indicate that the

conversion is complete. The TLV1544 and TLV1548 are designed to operate with a wide range of supply

voltages with very low power consumption. The power saving feature is further enhanced with a

software-programmed power-down mode and conversion rate. The converter incorporated in the device

features differential high-impedance reference inputs that facilitate ratiometric conversion, scaling, and

isolation of analog circuitry from logic and supply noise. A switched-capacitor design allows low-error

conversion over the full operating temperature range.