THS10064CDAR屬于集成電路（IC）的模數轉換器（ADC）。由美國德州儀器公司制造生產的THS10064CDAR模數轉換器（ADC）模數轉換器（ADC、A/D 或 A 轉 D）對模擬信號進行采樣，例如由麥克風采集的聲音或傳感器的輸出，然后將其轉換為數字信號。一般來說，數字輸出是二進制補碼二進制數，與輸入成比例。輸入類型可能是差分、偽差分或單端輸入。模數轉換器可按照位數、采樣率、輸入數、接口、轉換器數和架構（例如自適應增量、雙斜率、折疊、流水線、SAR、三角積分、兩步式）進行選擇。

FEATURES

High-Speed 6 MSPS ADC

4 Analog Inputs

Simultaneous Sampling of 4 Single-Ended

Signals or 2 Differential Signals or

Combination of Both

Differential Nonlinearity Error: ±1 LSB

Integral Nonlinearity Error: ±1.5 LSB

Signal-to-Noise and Distortion Ratio: 59 dB

at fI = 2 MHz

Auto-Scan Mode for 2, 3, or 4 Inputs

3-V or 5-V Digital Interface Compatible

Low Power: 216 mW Max

5-V Analog Single Supply Operation

Internal Voltage References . . . 50 PPM/°C

and ±5% Accuracy

Glueless DSP Interface

Parallel μC/DSP Interface

Integrated FIFO

Available in TSSOP Package

Pin Compatible With 12-Bit THS1206

APPLICATIONS

Radar Applications

Communications

Control Applications

High-Speed DSP Front-End

Automotive Applications

DESCRIPTION

The THS10064 is a CMOS, low-power, 10-bit, 6 MSPS

analog-to-digital converter (ADC). The speed, resolution,

bandwidth, and single-supply operation are suited for

applications in radar, imaging, high-speed acquisition, and

communications. A multistage pipelined architecture with

output error correction logic provides for no missing codes

over the full operating temperature range. Internal control

registers are used to program the ADC into the desired

mode. The THS10064 consists of four analog inputs,

which are sampled simultaneously. These inputs can be

selected individually and configured to single-ended or

differential inputs. An integrated 16 word deep FIFO allows

the storage of data in order to improve data transfers to the

processor. Internal reference voltages for the ADC (1.5 V

and 3.5 V) are provided.

An external reference can also be chosen to suit the dc

accuracy and temperature drift requirements of the

application. Two different conversion modes can be

selected. In single conversion mode, a single and

simultaneous conversion of up to four inputs can be

initiated by using the single conversion start signal

(CONVST). The conversion clock in single conversion

mode is generated internally using a clock oscillator

circuit. In continuous conversion mode, an external clock

signal is applied to the CONV_CLK input of the

THS10064. The internal clock oscillator is switched off in

continuous conversion mode.

The THS10064C is characterized for operation from 0°C

to 70°C, and the THS10064I is characterized for operation

from –40°C to 85°C.