SN74SSQEC32882ZALR屬于集成電路（IC）的專用邏輯器件。由美國德州儀器公司制造生產(chǎn)的SN74SSQEC32882ZALR專用邏輯器件專用邏輯 IC 設計提供應用特定的邏輯輸出類型，例如 BCD 速率倍增、可尋址掃描端口、總線終端陣列、CML 驅動器、比較器、ABT 掃描測試、二進制全加法器、互補對加逆變器、可配置緩沖器、觸點顫動消除器、晶體振蕩器、延遲元件、差分接收器、LVTTL 到 GTLP 收發(fā)器、存儲器解碼器、電源良好檢測器和分頻器。

1FEATURES

? JEDEC SSTE32882

? 1-to-2 Register Outputs and 1-to-4 Clock Pair

Outputs Support Stacked DDR3 RDIMMs

? CKE Powerdown Mode for Optimized System

Power Consumption

? 1.5V/1.35V/1.25V Phase Lock Loop Clock

Driver for Buffering One Differential Clock Pair

(CK and CK) and Distributing to Four

Differential Outputs

? 1.5V/1.35V/1.25V CMOS Inputs

? Checks Parity on Command and Address

(CS-Gated) Data Inputs

? Configurable Driver Strength

? Uses Internal Feedback Loop

? Optimized Power Consumption

APPLICATIONS

? DDR3 Registered DIMMs up to DDR3-1866

? DDR3L Registered DIMMs up to DDR3L-1600

? DDR3U Registered DIMMs up to DDR3U-1333

? Single-, Dual- and Quad-Rank RDIMM

DESCRIPTION

This 1:2 or 26-bit 1:2 and 4-bit 1:1 registering clock driver with parity is designed for operation on DDR3

registered DIMMs with VDD of 1.5 V, on DDR3L registered DIMMs with VDD of 1.35 V and on DDR3U registered

DIMMs with VDD of 1.25 V.

All inputs are 1.5 V, 1.35V and 1.25 V CMOS compatible. All outputs are CMOS drivers optimized to drive DRAM

signals on terminated traces in DDR3 RDIMM applications. The clock outputs Yn and Yn and control net outputs

DxCKEn, DxCSn and DxODTn can be driven with a different strength and skew to optimize signal integrity,

compensate for different loading and equalize signal travel speed.

The SN74SSQEC32882 has two basic modes of operation associated with the Quad Chip Select Enable

(QCSEN) input. When the QCSEN input pin is open (or pulled high), the component has two chip select inputs,

DCS0 and DCS1, and two copies of each chip select output, QACS0, QACS1, QBCS0 and QBCS1. This is the

QuadCS disabled mode. When the QCSEN input pin is pulled low, the component has four chip select inputs

DCS[3:0], and four chip select outputs, QCS[3:0]. This is the QuadCS enabled mode. Through the remainder of

this specification, DCS[n:0] will indicate all of the chip select inputs, where n=1 for QuadCS disabled, and n=3 for

QuadCS enabled. QxCS[n:0] will indicate all of the chip select outputs.

The device also supports a mode where a single device can be mounted on the back side of a DIMM. If

MIRROR=HIGH, Input Bus Termination (IBT) has to stay enabled for all input signals in this case.

The SN74SSQEC32882 operates from a differential clock (CK and CK). Data are registered at the crossing of

CK going HIGH, and CK going LOW. This data could be either re-driven to the outputs or it could be used to

access device internal control registers.

The input bus data integrity is protected by a parity function. All address and command input signals are added

up and the last bit of the sum is compared to the parity signal delivered by the system at the input PAR_IN one

clock cycle later. If they do not match the device pulls the open drain output ERROUT LOW. The control signals

(DCKE0, DCKE1, DODT0, DODT1, DCS[n:0]) are not part of this computation.

The SN74SSQEC32882 implements different power saving mechanisms to reduce thermal power dissipation and

to support system power down states. By disabling unused outputs the power consumption is further reduced.

The package is optimized to support high density DIMMs. By aligning input and output positions towards DIMM

finger signal ordering and SDRAM ballout the device de-scrambles the DIMM traces allowing low cross talk

design with low interconnect latency.

Edge controlled outputs reduce ringing and improve signal eye opening at the SDRAM inputs.