SN74LVC652APWT屬于集成電路（IC）的緩沖器驅動器接收器收發器。由美國德州儀器公司制造生產的SN74LVC652APWT緩沖器，驅動器，接收器，收發器邏輯緩沖器、驅動器、接收器和收發器允許隔離對某個電路的邏輯信號的訪問，以用于另一電路。緩沖器將其輸入信號（不變或反相）傳遞到其輸出，并可能用于清除弱信號或驅動負載。在布爾邏輯仿真器中，緩沖器主要用于增加傳播延遲。邏輯接收器和收發器允許在數據總線之間進行隔離通信。

FEATURES

· Operate From 1.65 V to 3.6 V

· Inputs Accept Voltages to 5.5 V

· Max t pd of 7.4 ns at 3.3 V

· Typical V OLP (Output Ground Bounce) <0.8 V

at V CC = 3.3 V, TA = 25°C

· Typical V OHV (Output VOH Undershoot) >2 V at

V CC = 3.3 V, TA = 25°C

· Support Mixed-Mode Signal Operation on All

Ports (5-V Input/Output Voltage With 3.3-V

VCC)

· Ioff Supports Partial-Power-Down Mode

Operation

· ESD Protection Exceeds JESD 22

– 2000-V Human-Body Model (A114-A)

– 200-V Machine Model (A115-A)

– 1000-V Charged-Device Model (C101)

DESCRIPTION/ORDERING INFORMATION

The SN54LVC652A octal bus transceiver and register is designed for 2.7-V to 3.6-V VCC operation, and the

SN74LVC652A octal bus transceiver and register is designed for 1.65-V to 3.6-V VCC operation.

These devices consist of bus transceiver circuits, D-type flip-flops, and control circuitry arranged for multiplexed

transmission of data directly from the data bus or from the internal storage registers.

Output-enable (OEAB and OEBA) inputs are provided to control the transceiver functions. Select-control (SAB

and SBA) inputs are provided to select whether real-time or stored data is transferred. The circuitry used for

select control eliminates the typical decoding glitch that occurs in a multiplexer during the transition between

stored and real-time data. A low input selects real-time data, and a high input selects stored data. Figure 1

illustrates the four fundamental bus-management functions that are performed with the 'LVC652A devices.

Data on the A or B data bus, or both, is stored in the internal D-type flip-flops by low-to-high transitions at the

appropriate clock (CLKAB or CLKBA) inputs, regardless of the select- or enable-control pins. When SAB and

SBA are in the real-time transfer mode, it is possible to store data without using the internal D-type flip-flops by

simultaneously enabling OEAB and OEBA. In this configuration, each output reinforces its input. When all other

data sources to the two sets of bus lines are at high impedance, each set of bus lines remains at its last state.

Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators

in a mixed 3.3-V/5-V system environment.

These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the

outputs, preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OEBA should be tied to VCC through a

pullup resistor and OEAB should be tied to GND through a pulldown resistor; the minimum value of the resistor is

determined by the current-sinking/current-sourcing capability of the driver.