SN65HVD232QDG4屬于集成電路（IC）的驅動器接收器收發器。由美國德州儀器公司制造生產的SN65HVD232QDG4驅動器，接收器，收發器該系列產品的主要功能是提供必需的硬件資源，以通過延長電纜或印制線進行通信。確切的功能會因所采用的通信協議而異，可能包括諸如瞬態抑制之類的功能，這些功能對于通信用途可能并非絕對必要，但對于可能的使用環境卻是明智之選。

FEATURES

Qualified for Automotive Applications

ESD Protection Exceeds 2000 V Per

MIL-STD-883, Method 3015; Exceeds 200 V

Using Machine Model (C = 200 pF, R = 0)

Operates With a 3.3-V Supply

Low Power Replacement for the PCA82C250

Footprint

Bus/Pin ESD Protection Exceeds 15-kV HBM

Controlled Driver Output Transition Times for

Improved Signal Quality on the SN65HVD230Q

and SN65HVD231Q

Unpowered Node Does Not Disturb the Bus

Compatible With the Requirements of the

ISO 11898 Standard

Low-Current SN65HVD230Q Standby Mode

370 μA Typical

Low-Current SN65HVD231Q Sleep Mode

0.1 μA Typical

Designed for Signaling Rates? Up To

1 Megabit/Second (Mbps)

Thermal Shutdown Protection

Open-Circuit Fail-Safe Design

DESCRIPTION

The SN65HVD230Q, SN65HVD231Q, and SN65HVD232Q controller area network (CAN) transceivers are

designed for use with the Texas Instruments TMS320Lx240x 3.3-V DSPs with CAN controllers, or with

equivalent devices. They are intended for use in applications employing the CAN serial communication physical

layer in accordance with the ISO 11898 standard. Each CAN transceiver is designed to provide differential

transmit capability to the bus and differential receive capability to a CAN controller at speeds up to 1 Mbps.

Designed for operation in especially-harsh environments, these devices feature cross-wire protection,

loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range.

The transceiver interfaces the single-ended CAN controller with the differential CAN bus found in industrial,

building automation, and automotive applications. It operates over a –2-V to 7-V common-mode range on the

bus, and it can withstand common-mode transients of ±25 V.

On the SN65HVD230Q and SN65HVD231Q, RS (pin 8) provides three different modes of operation:

high-speed, slope control, and low-power modes. The high-speed mode of operation is selected by connecting

pin 8 to ground, allowing the transmitter output transistors to switch on and off as fast as possible with no

limitation on the rise and fall slopes. The rise and fall slopes can be adjusted by connecting a resistor to ground

at pin 8, since the slope is proportional to the pin’s output current. This slope control is implemented with external

resistor values of 10 kΩ, to achieve a 15-V/μs slew rate, to 100 kΩ, to achieve a 2-V/μs slew rate.

The circuit of the SN65HVD230Q enters a low-current standby mode during which the driver is switched off and

the receiver remains active if a high logic level is applied to RS (pin 8). The DSP controller reverses this

low-current standby mode when a dominant state (bus differential voltage > 900 mV typical) occurs on the bus.

The unique difference between the SN65HVD230Q and the SN65HVD231Q is that both the driver and the

receiver are switched off in the SN65HVD231Q when a high logic level is applied to RS (pin 8) and remain in

this sleep mode until the circuit is reactivated by a low logic level on RS.

The Vref (pin 5 on the SN65HVD230Q and SN65HVD231Q) is available as a VCC/2 voltage reference.

The SN65HVD232Q is a basic CAN transceiver with no added options; pins 5 and 8 are NC, no connection.