最新无码a∨在线观看,一本av高清一区二区三区,亚洲熟妇色l20p,宅男噜噜69av,中出あ人妻熟女中文字幕

SN65C3243

具有 +/-15kV ESD 保護(hù)的 3V 至 5.5V 多通道 1Mbps RS-232 線路驅(qū)動(dòng)器/接收器; ? Operates With 3-V to 5.5-V VCC Supply\n? Always-Active Noninverting Receiver Output (ROUT2B)\n? Low Standby Current . . . 1 μA Typ\n? External Capacitors . . . 4 × 0.1 μF\n? Accepts 5-V Logic Input With 3.3-V Supply\n? Inter-Operable With SN65C3238, SN75C3238\n? Supports Operation From 250 kbit/s to 1 Mbit/s\n? RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM)\n? Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II\n? APPLICATIONS \n? Battery-Powered Systems\n? PDAs\n? Notebooks\n? Laptops\n? Palmtop PCs\n? Hand-Held Equipment;

The SN65C3243 and SN75C3243 consist of three line drivers, five line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). This device provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, this device includes an always-active noninverting output (ROUT2B), which allows applications using the ring indicator to transmit data while the device is powered down. The device operates at data signaling rates up to 1 Mbit/s and an increased slew-rate range of 24 V/μs to 150 V/μs. Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low, both drivers and receivers (except ROUT2B) are shut off, and the supply current is reduced to 1 μA. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high and should be done when driving a serial mouse. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than ?2.7 V or has been between ?0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid data) if all receiver input voltages are between ?0.3 V and 0.3 V for more than 30 μs. Refer to Figure 5 for receiver input levels.

SN65C3243

3V TO 5.5V MULTICHANNEL COMPATIBLE RS232 LINE DRIVERS/RECEIVERS

SN65C3243

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER

SN65C3243

3-V TO 5.5-V TWO-CHANNEL RS-232 1-MBIT/S LINE DRIVERS/RECEIVERS WITH ?15-kV IEC ESD PROTECTION

SN65C3243

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER

SN65C3243_15

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER

SN65C3243DBR

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER

SN65C3243DBR

3V TO 5.5V MULTICHANNEL COMPATIBLE RS232 LINE DRIVERS/RECEIVERS

SN65C3243DBR

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER

SN65C3243DBRE4

3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER