最新无码a∨在线观看,一本av高清一区二区三区,亚洲熟妇色l20p,宅男噜噜69av,中出あ人妻熟女中文字幕

PCA9532BS

16-bit I2C LED dimmer

DESCRIPTION ThePCA9532isa16-bitI2C-busandSMBusI/OexpanderoptimizedfordimmingLEDsin256discretestepsforRed/Green/Blue(RGB)colormixingandbacklightapplications. ThePCA9532containsaninternaloscillatorwithtwouserprogrammableblinkratesanddutycyclescoupledto

PCA9532BS

16-bit I2C-bus LED dimmer; ? 16 LED drivers (on, off, flashing at a programmable rate)\n? Two selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 second and 6.58 milliseconds)\n? 256 brightness steps\n? Input/outputs not used as LED drivers can be used as regular GPIOs\n? Internal oscillator requires no external components\n? I2C-bus interface logic compatible with SMBus\n? Internal power-on reset\n? Noise filter on SCL/SDA inputs\n? Active LOW reset input\n? 16 open-drain outputs directly drive LEDs to 25 mA\n? Controlled edge rates to minimize ground bounce\n? No glitch on power-up\n? Supports hot insertion\n? Low standby current\n? Operating power supply voltage range of 2.3 V to 5.5 V\n? 0 Hz to 400 kHz clock frequency\n? ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101\n? Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\n? Packages offered: SO24, TSSOP24, HVQFN24\n;

The PCA9532 is a 16-bit I2C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and backlight applications.\nThe PCA9532 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED.\nThe initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 seconds. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 200 mA per package (100 mA per octal).\nTo blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chipset, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8575 or PCA9555. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc.\nThe active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off).\nThree hardware address pins on the PCA9532 allow eight devices to operate on the same bus.\n

9532

MACHINESCREWPANPHILLIPS10-32

BD9532EKN

StepdownDC/DCconverterControllerforNOTEPC

BD9532EKN

SwitchingRegulatorsforDDR-SDRAMCores

CAT9532

CatalystSemiconductor

I2CInterfaced16-bitLEDDimmer,I2CInterfaced16-bitLEDBlinker Features ■256discretebrightnessstepsforeasyLEDdimmingandcolormixing ■twoprogrammableblinkingratebetween0.625secand1.6secforCAT9532;0.02secand6.4secforCAT9552 ■eliminatesrepeatedcommand

CAT9532

16-bitProgrammableLEDDimmerwithI2CInterface

CAT9532

16-bitProgrammableLEDDimmer

CAT9532WI

16-bitProgrammableLEDDimmerwithI2CInterface

CAT9532WI

16-bitProgrammableLEDDimmerwithI2CInterface