AFE44I30YZR屬于集成電路（IC）的模擬前端（AFE）。由美國德州儀器公司制造生產的AFE44I30YZR模擬前端（AFE）模擬前端 (AFE) 是一種用于信號調節的半導體器件，由模擬放大器、運算放大器、濾波器和集成電路構成。這種可配置功能塊能連接各種傳感器。分辨率范圍從 8 位至 42 位不等，通道數范圍為 1 至 256 個。

1 Features

1? Supports signal acquisition of up to 24 phases

? Flexible allocation of 6 LED, 4 PD in each phase

? Simultaneous signal acquisition from different

sensors at different data rates

? Accurate, continuous heart-rate monitoring:

– System SNR up to 108-dB at 16 μA PD current

– Low current for continuous operation on a

wearable device with a typical value: 15 μA for

an LED, 20 μA for the receiver

? Transmitter:

– Supports common anode LED configuration

– 8-Bit programmable LED current with range

adjustable from 25 mA to 250 mA

– Mode to fire two LEDs in parallel with

independent per-phase current control

– Programmable LED on-time per-phase

– Simultaneous support of 6 LEDs for SpO2,

HRM, or multi-wavelength HRM

? Receiver:

– Supports 4 time-multiplexed photodiode inputs

– 2 parallel receivers (two sets of TIA/filter)

– Individual ambient offset subtraction DAC at

each TIA Input with 8-bit per-phase control and

range adjustable up to 255-μA

– Individual LED offset subtraction DAC at each

TIA input with 5-bit per-phase control and 15.5-

μA range

– Close to 100 dB ambient rejection up to 10 Hz

– Noise filtering with programmable bandwidth

– Transimpedance Gain: 3.7 kΩ to 1 MΩ

? Supports external clock and internal oscillator

modes

? Option to acquire data synchronized with a system

master clock

? Automatic cancellation of DC from ambient, LED

? FIFO with 128-sample depth

? I2C interface

? 2.6-mm × 2.1-mm DSBGA, 0.4-mm pitch

? Supplies: Rx: 1.7 V-1.9 V (LDO bypass); 1.9 V-3.6

V (LDO enabled), Tx: 3 V-5.5 V, IO: 1.7-3.6 V

2 Applications

? Optical heart-rate monitoring (HRM) for

wearables, hearables

? Heart-rate variability (HRV)

? Pulse oximetry (SpO2) measurements

3 Description

The AFE44I30 is an analog front-end for optical biosensing

applications, such as heart-rate monitoring

(HRM) and saturation of peripheral capillary oxygen

(SpO2). The device supports up to six switching lightemitting

diodes (LEDs) and up to four photodiodes.

Up to 24 signal phases can be defined and the signal

can be acquired from each phase in a synchronized

manner. The current from the photodiode is

converted into voltage by the transimpedance

amplifier (TIA) and digitized using an analog-to-digital

converter (ADC). The ADC code can be stored in a

128-sample First in, First out (FIFO) block. The FIFO

can be read out using a I2C interface. The AFE also

has a fully-integrated LED driver with an 8-bit current

control. The device has a high dynamic range

transmit-and-receive circuitry that helps with the

sensing of very small signal levels.