74AVCB164245GRE4屬于集成電路（IC）的轉換器電平移位器。由美國德州儀器公司制造生產的74AVCB164245GRE4轉換器，電平移位器邏輯轉換器或電平移位器 IC 可用于在數字邏輯設備之間傳遞信息，這些設備可在不同/不兼容的供電電壓下工作，或可實現不同的信令方式。例如，可以將需要 5 V 電源的數字輸出傳感器連接到具有 3.3 V I/O 電源的 FPGA，或者在 CMOS 或 TTL 等單端信令方式與 PECL 或 LVDS 等差分技術之間進行轉換。

FEATURES

· Member of the Texas Instruments Widebus?

Family

· DOC? Circuitry Dynamically Changes Output

Impedance, Resulting in Noise Reduction

Without Speed Degradation

· Dynamic Drive Capability Is Equivalent to

Standard Outputs With IOH and IOL of ±24 mA

at 2.5-V VCC

· Control Inputs VIH/VIL Levels Are Referenced

to VCCB Voltage

· If Either VCC Input Is at GND, Both Ports Are in

the High-Impedance State

· Overvoltage-Tolerant Inputs/Outputs Allow

Mixed-Voltage-Mode Data Communications

· Ioff Supports Partial-Power-Down Mode

Operation

· Fully Configurable Dual-Rail Design Allows

Each Port to Operate Over Full 1.4-V to 3.6-V

Power-Supply Range

· Latch-Up Performance Exceeds 100 mA Per

JESD 78, Class II

· ESD Protection Exceeds JESD 22

– 2000-V Human-Body Model (A114-A)

– 200-V Machine Model (A115-A)

– 1000-V Charged-Device Model (C101)

DESCRIPTION

This 16-bit (dual-octal) noninverting bus transceiver uses two separate configurable power-supply rails. The

A port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B port is designed to

track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage

bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.

The SN74AVCB164245 is designed for asynchronous communication between data buses. The device transmits

data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the

direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are

effectively isolated.

The SN74AVCB164245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB.

To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup

resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,

preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND,

both ports are in the high-impedance state.